Waterless mold removal for homes and businesses near the border

Dry Ice Blasting Mold in SAN YSIDRO, California

Dry Ice Blasting Mold in SAN YSIDRO, California is a waterless remediation method that lifts mold off wood, block, and steel without soaking your structure. We handle homes and commercial buildings from San Ysidro Proper to the Beyer Boulevard Corridor, and we run dry ice mold remediation SAN YSIDRO California jobs seven days a week. If you have black mold growth, a musty odor, or water damage mold after a slab leak, call (833) 929-5837.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service San Ysidro
Careful work. Honest options.
About this service

What Dry Ice Blasting Mold in SAN YSIDRO, California Involves

Dry Ice Blasting Mold in SAN YSIDRO, California is a remediation service that fires compressed dry ice pellets at 300 to 600 PSI to strip mold, spores, and staining off framing lumber, concrete block, and metal ductwork. The pellets hit at roughly minus 109 degrees Fahrenheit, freeze the mold, and lift it without abrasives. There is no water, no sand, and no chemical residue left behind, so we can blast a crawl space or attic and leave the wood dry enough to inspect the same day.

Most SAN YSIDRO calls we run start with a moisture meter reading above 16 percent on drywall or lumber. That usually traces back to a slab leak, a bathroom ceiling mold problem from poor ventilation, or crawl space mold after winter rain. Because we are 4 years into this work and have handled hundreds of South County jobs, we know which neighborhoods flood first. If you are searching for affordable dry ice mold remediation in SAN YSIDRO, start with a boroscope inspection camera check before anyone quotes you.

  • ✓ No Secondary Water Damage
  • ✓ Reaches Tight Framing
  • ✓ Cuts Remediation Time
  • ✓ Cleaner Clearance Testing
What's included

What Our Dry Ice Blasting Mold Service Includes

Every job includes inspection, containment, blasting, antimicrobial treatment, and clearance testing. If your job needs something beyond that, like duct cleaning or full reconstruction, we tell you up front and quote it separately so there are no surprises on the invoice.

✓

Full Mold Inspection

Moisture meter, thermal imaging camera, and boroscope inspection camera readings across the affected area. You get photos and a written scope before we start.

✓

Containment and HEPA Filtration

Poly sheeting containment with zipper doors, negative air machine, and air scrubber with HEPA filters. We seal HVAC registers so spores do not spread during blasting.

✓

Dry Ice Blasting

Compressed dry ice pellets at 300 to 600 PSI strip mold, spores, and staining from framing lumber, block, and metal. No water, no abrasives, no chemical residue.

✓

Antimicrobial Treatment

Sporicidal cleaner such as Benefect or Concrobium applied to the blasted substrate, plus a mold encapsulant on porous wood where growth was heavy.

✓

Clearance Testing

Air sampling pump and spore trap samples sent to an accredited lab. Results in 24 to 48 hours, with a written report you can share with a buyer, landlord, or insurer.

How it works

Our Dry Ice Blasting Mold Process

01

Inspection and Mapping

We start with a moisture meter and thermal imaging camera to find every wet zone, not just the visible mold. A boroscope inspection camera goes into wall cavities and joist bays. This takes 45 to 90 minutes and tells us whether dry ice blasting is the right method or whether material has to come out.

02

Containment Setup

We build poly sheeting containment with zipper doors and run a negative air machine with HEPA filters so spores do not migrate into clean rooms. Technicians suit up in personal protective equipment, and we seal HVAC registers to prevent HVAC mold contamination during the blast.

03

Dry Ice Blasting

Our technicians run the dry ice blasting machine at 300 to 600 PSI, working top-down and back-to-front. Mold, spores, and surface staining come off framing lumber, block, and ductwork. A 300 square foot crawl space takes about 4 hours. We keep a HEPA vacuum running the whole time to capture debris at the source.

04

Antimicrobial and Encapsulant

After blasting, we apply a sporicidal cleaner such as Benefect or Concrobium to the affected substrate, then a mold encapsulant on porous wood where growth was heavy. This step locks down any remaining spores and gives the surface a sealed finish.

05

Clearance Testing

We run an air sampling pump and take spore trap samples for post remediation mold testing. Results come back in 24 to 48 hours from an accredited lab. If the numbers are clean, we remove containment and hand you the report. If not, we re-blast at no extra charge.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry Ice Blasting Machine

Fires food-grade dry ice pellets at 300 to 600 PSI to strip mold and staining without water or abrasives. Adjustable pressure lets us clean softwood without gouging it.

Thermal Imaging Camera

Finds hidden moisture behind drywall and in ceiling cavities before we cut or blast. It shows us where water damage mold is likely to be growing.

Boroscope Inspection Camera

Slides into wall cavities and joist bays to confirm growth depth. It tells us whether dry ice blasting will work or whether material has to come out.

Negative Air Machine and Air Scrubber

Maintains negative pressure inside containment and filters airborne spores through HEPA filters. Keeps the rest of your home or business clean during blasting.

HEPA Vacuum

Captures debris and spores at the source while we blast. We run ProTeam and 3M HEPA units on every job, then vacuum all surfaces before we break containment.

Air Sampling Pump

Draws a measured volume of air through spore traps for lab analysis. Used before blasting and again for post remediation mold testing.

Dehumidifier and Dri-Eaz Equipment

Finishes the dry-down after water damage mold remediation. We run Dri-Eaz and Phoenix Restoration Equipment units when the source was a leak or flood.

Real results

Before and after.

Border Village Crawl Space Recovery

Before

A slab leak had soaked roughly 500 square feet of crawl space for over a week. Joists showed black mold growth, and the musty odor was reaching the first floor of the duplex.

After

We dry ice blasted the joists and subfloor in a single 6-hour shift, treated with RMR-86 and an encapsulant, and ran clearance testing 48 hours later. Spore counts dropped below the outdoor baseline.

Ocean View Hills Attic Cleanup

Before

Two wet winters left mold on about 350 square feet of roof sheathing and rafters. A previous contractor quoted full sheathing replacement at over $6,000.

After

Dry ice blasting removed the growth without damaging the wood, and we added ventilation baffles while on site. Post remediation mold testing passed on the first attempt.

Camino De La Plaza Restaurant Ducts

Before

HVAC mold contamination in the kitchen plenum and duct runs was pushing musty odors into the dining room. The restaurant could not afford to close for a multi-day job.

After

We worked overnight, dry ice blasted the plenum and accessible ducts, and fogged the cavities with Benefect. Air sampling the next morning came back clean.

Problems we solve

Mold Problems We Solve Across SAN YSIDRO

Most of the calls we get are not about a little surface growth. They are about a crawl space that stays wet, an attic that never vents, or a bathroom ceiling that keeps coming back. Here is what we fix and why it matters.

Ask a pro →
01

Crawl space mold after winter rain

We dry ice blast the joists and subfloor, apply a sporicidal cleaner, and seal the wood with a mold encapsulant. We also flag the drainage or vapor barrier issue causing the moisture so it does not return next season.

↗
02

Attic mold from poor ventilation

We run a boroscope inspection camera to check sheathing depth, then dry ice blast the affected rafters and decking. In most cases the lumber stays, which saves thousands over full sheathing replacement.

↗
03

Bathroom ceiling mold that keeps returning

We inspect the exhaust fan and ducting, then dry ice blast the ceiling substrate and treat with an antimicrobial solution. If the drywall is too far gone, we remove and replace just that section.

↗
04

HVAC mold contamination in ductwork

We seal the system, dry ice blast the plenum and accessible duct interiors, then follow with a mold fogging treatment to reach voids blasting cannot. NADCA-aligned methods keep debris out of the living space.

↗
Proof you can check

Licensed, Certified, and Local

✓
IICRC AMRT (Applied Microbial Remediation Technician)IICRC
✓
IICRC WRT (Water Restoration Technician)IICRC
✓
ACAC CMI (Certified Mold Inspector)American Council for Accredited Certification
✓
ACAC CMR (Certified Mold Remediator)American Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs run $1,200 to $3,800 in 2026, depending on square footage and access. A small bathroom ceiling mold job can come in under $1,000, while a 1,000 square foot commercial crawl space with HVAC mold contamination runs higher. We give you a fixed price after the inspection, and clearance testing is included.

Yes. Dry ice is food-grade carbon dioxide, and it sublimates into gas with no chemical residue left on your framing or ductwork. We still build poly sheeting containment and run a negative air machine with HEPA filters, because the mold spores themselves are the hazard, not the blasting media. Technicians wear full personal protective equipment on every job.

We do. Mold Remediation Service San Ysidro has run dry ice blasting mold removal near me SAN YSIDRO calls since 2022, covering San Ysidro Proper, Border Village, Los Olivos, Ocean View Hills, Sunset Gardens, and the Camino De La Plaza corridor. Call (833) 929-5837 and we will schedule an inspection, often the same day.

Traditional removal means scrubbing, sanding, or wet blasting, and often tearing out drywall, insulation, and lumber. Dry ice blasting cleans the surface without water or abrasives, so you keep more of the original structure and skip the 2 to 3 day drying cycle. On attic mold and crawl space mold, that usually saves both time and material cost.

Ready when you are

Get Dry Ice Blasting Mold in SAN YSIDRO, California

We are licensed, insured, and we answer the phone 24/7. Call (833) 929-5837 and we will schedule an inspection, often the same day, and give you a fixed price before any work starts.

Book Inspection (833) 929-5837 →
Request an appointment

Contact Our SAN YSIDRO Mold Team

Call (833) 929-5837 any time, day or night, and a real person answers. We schedule inspections same-day when possible and dispatch emergency crews 24/7 for active leaks and spreading mold. If you prefer email, send photos and your address to info@moldremediationservicesanysidro.com and we will follow up with next steps.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837